ESP8266 IOT Board(Arduino IDE or NodeMCU Lua Programming)

Introduction

This is a ESP8266 IOT board- our take on an 'all-in-one' ESP8266 WiFi development board with built in USB and battery charging. It’s an ESP8266 WiFi module with all the extras you need, The most important part is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can program the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. We wired up a USB-Serial chip that can upload code. It also has auto-reset so no noodling with pins and reset button pressings. To make it easy to use for portable projects, we added a connector for 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The board will automatically switch over to USB power when its available. Comes fully assembled and tested, with a USB interface that lets you quickly use it with the Arduino IDE or NodeMCU Lua. (It comes preprogrammed with the Lua interpretter) We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)

Model: DPO82666E

Features

Dimensions(mm): 50.0(L)x35.0(W)x7.3(H)
Light weight
ESP8266 @ 80MHz with 3.3V logic/power
4MB of FLASH (32 MBit)
Built in WiFi 802.11 b/g/n
3.3V regulator with 500mA peak current output
CP2012 USB-Serial converter onboard with 921600 max baudrate for uploading
Auto-reset support for getting into bootload mode before firmware upload
9 x GPIO pins - can also be used as I2C and SPI
1 x analog inputs 1.0V max
Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
Power/enable pin
4 mounting holes
Reset button

Interface Function

Micro USB port - it use for upload the program and update firmware,you can also charge the battery
Battery interface - you can power this board with a lipo battery by this port
Reset button - to have a reset
Flash button - it use for update the firmware

Usage

Hardware installation

1.Power Management

It's easy to power it both when connected to a computer as well as lipo battery

2.Using NodeMCU Lua

Prepareation

ESP8266 IOT board comes pre-programmed with NodeMCU's lua interpretter. The Lua interpretter runs on the ESP8266 and you can type in commands and read out the results over serial. In order to upload code to the ESP8266 and use the serial console, connect any data-capable micro USB cable to the IOT board and the other side to your computer's USB port.Maybe you need to install the cp2102 USB driver,you can download driver hear.

Load the firmware

If you want to burning the firmware,please refer the following steps. Our ESP8266 IOT Board had comes preprogrammed with the Lua interpretter.You can direct use it.
1.Download the tool nodemcu-flasher-master,unzip it and choose the right loading software according to your computer system(32 bit or 64 bit) ,open it you can see as bellow:

Note:The COM Port you should choose what are you using.
2.Download the firmware and click the config button,then load the firmware.

3.Then click the "Flash" button to load the firmware,as bellow:

when the firmware is flashing the blue led in the ESP8266 IOT Board will continuous flashing .

Open up serial console

Next up, we need to choose a development tool such as LuaLoader/ NodeMCUStudioIDE/ Decoda. Now do a demonstration with the LuaLoader.
First, disconnected the usb cable and run the LuaLoader;

Click the menu "Setting", choose the"Comm Port Settings", and it'll popup a "Serial Advanced Setting", you could set the port there.

Then connect the USB cable with it, and click the "Connect" button on the top of menu.

Input command statement into the below edit box.

and it will output that:

Also you use some of the function of the display on the right of the NodeMCU Lua.
1.GPIO Function

2.you can check the information about the chip and restart NodeMcu.like as bellow:

3.Connect the wireless networks around you

4.Download the program

In its bottom right corner you will see something about download program function button.

3.Using Arduino IDE

1.Install the Arduino IDE 1.6.4 or greater Download Arduino IDE from Arduino.cc (1.6.4 or greater) - don't use 1.6.2! You can use your existing IDE if you have already installed it.（We're seeing some difficulties with IDE 1.6.6 so please try 1.6.5 or skip 1.6.6!） You can also try downloading the ready-to-go package from the ESP8266-Arduino project, if the proxy is giving you problems

2.Install the COM/Serial port driver for USB. In order to upload code to the ESP8266 and use the serial console, connect any data-capable micro USB cable to ESP8266 IOT Board and the other side to your computer's USB port.

3.Install the ESP8266 Board Package
Open Arduino v1.6.4 preferences

400px

Enter the below URL into Additional Board Manager URLs field

http://arduino.esp8266.com/stable/package_esp8266com_index.json

Next, use the Board manager to install the ESP8266 package

Note: you should close the Arduino v1.6.4 and restart it again.

4.Setup ESP8266 Support
When you've restarted, select Generic ESP8266 Module from the Tools->Board dropdown

80 MHz as the CPU frequency

15200 baud upload speed (You can also try faster baud rates, we were able to upload at a blistering 921600 baud but sometimes it fails & you have to retry)

The matching COM port for your FTDI or USB-Serial cable