Difference between revisions of "Crowtail- LoRa RA-08H"
(→Usage) |
|||
Line 118: | Line 118: | ||
==Resources == | ==Resources == | ||
[https://www.elecrow.com/wiki/index.php?title=File:Crowtail-_LoRa_RA-08H-V1.2-eagle_file.zip Crowtail-_LoRa_RA-08H-V1.2-eagle_file.zip ]<br> | [https://www.elecrow.com/wiki/index.php?title=File:Crowtail-_LoRa_RA-08H-V1.2-eagle_file.zip Crowtail-_LoRa_RA-08H-V1.2-eagle_file.zip ]<br> | ||
− | [https://www.elecrow.com/wiki/index.php?title=File:Lora.zip Lora_code.zip] | + | [https://www.elecrow.com/wiki/index.php?title=File:Lora.zip Lora_code.zip]<br> |
+ | [https://www.elecrow.com/wiki/index.php?title=File:Ra-08h_v1.1.0_specification.pdf Ra-08h_v1.1.0_specification.pdf]<br> | ||
+ | [https://www.elecrow.com/wiki/index.php?title=File:RA-08_AT_Instruction.pdf RA-08_AT_Instruction.pdf] |
Revision as of 04:28, 26 October 2022
Contents
Description
Crowtail - LoRa RA-08H uses the Ra-08H (ASR6601) module, which has ultra long distance spread spectrum communication. Its chip ASR6601 is a general-purpose LPWAN wireless communication SoC integrated with RF transceiver, modem and a 32-bit RISC MCU. The Ra-08H module supports LoRa modulation and traditional (G) FSK modulation under the LPWAN use case; The transmitter also supports BPSK modulation and (G) MSK modulation.
The Ra-08H module provides ultra long range and ultra-low power consumption communication for LPWAN applications, and can be widely used in intelligent instruments, supply chain and logistics, home building automation, security systems, remote irrigation systems and other scenarios.
Specifications
- Voltage: 3.3~5V
- Theoretical maximum transmission power+22dBm
- Supported frequency band: 803~930MHZ
- High sensitivity: -138dBm@125KzSF12
- Support spread spectrum factor: SF5/SF6/SF7/SF8/SF9/SF10/SF11/SF12
- Embedded memory: 128KB FLASH, 16KB SRAM
- Support LoRa/(G) FSK/BPSK/(G) MSK modulation
- Maximum transmission distance 1KM (ideal value for open space)
- With download and communication switching functions, users can customize programming
- Configure the first generation IPEX seat
- Dimension (mm): 40 (L) * 20 (W) * 7.5 (H)
Schematic
Usage
Hardware Connection
- STEP1 Prepare the below stuffs:
Crowduino Uno Base Shield Crowtail- LoRa RA-08H Get one now Get one now Get one now
- STEP2 Plug Crowtail-Base Shield into Crowduino Uno;
- STEP3 Plug Crowtail-LoRa RA-08H to D2 D3 slot of Crowtail-Base Shield via 4 pin Crowtail Cable;
- STEP4 Connect Crowduino Uno to PC via a Mini USB cable.
NOTE If we don't have Crowtail Base Shield, We also can directly connect this module to Crowduino Uno as below.
Crowduino Uno Crowtail- LoRa RA-08H D2 TX D3 RX 3.3V VCC GND GND
Software
- STEP1 Configure controller board&communication port
- On top of the Arduino IDE, click “Tools>Board>” and select “Arduino Uno” from the available options
- STEP2 Select the COM port that indicates Arduino Uno. Please note that the actual numbers after the “COM” word will vary from computer to computer, so they could be different from the ones shown in the figure.
- STEP3 Open the program in the Arduino IDE
#include <SoftwareSerial.h> // Pin2接LORA的TXD // Pin3接LORA的RXD SoftwareSerial LORA(2, 3); char val; void setup() { Serial.begin(9600); Serial.println("LORA is ready!"); LORA.begin(9600); } void loop() { if (Serial.available()) { val = Serial.read(); LORA.print(val); delay(10); } if (LORA.available()) { val = LORA.read(); Serial.print(val); delay(10); } }
- STEP5 Open the AT command description of Ra-08H, find the relevant command, open the serial port monitor, and input the command into the serial port monitor, for example, enter [AT+CGSN?] Command, click Send, and the reply code will be received:
- +CGSN=1E612A8482213201
- OK
FAQS
You can post your questions on our forum or contact with techsupport@elecrow.com for technology support.
Resources
Crowtail-_LoRa_RA-08H-V1.2-eagle_file.zip
Lora_code.zip
Ra-08h_v1.1.0_specification.pdf
RA-08_AT_Instruction.pdf