The store will not work correctly when cookies are disabled.
elecrow logo
  • Shops
  • Projects
    • Categories
    • 2nd Electronics Design Contest 2nd Electronics Design Contest
    • PCB PCB
    • DIY Electronics DIY Electronics
    • Arduino Arduino
    • ESP ESP
    • Raspberry Pi Raspberry Pi
    • IoT Hardware Contest IoT Hardware Contest
    • LoRa LoRa
    • PCB Assembly PCB Assembly
    • 3D Printing 3D Printing
    • View All Category
    • Featured Projects
    • IOL HAT On, Complexity Off - Industrial IoT Made Simple!
      IOL HAT On, Complexity Off - Industrial IoT Made Simple!
      ✈️ UAV Fixed Wing design– High-Lift Wing with Control Surfac
      ✈️ UAV Fixed Wing design– High-Lift Wing with Control Surfac
      CrowPanel UART Settings Sender for ESP32-S3
      CrowPanel UART Settings Sender for ESP32-S3
    • We Recommend
    • Lastest Projects
    • Most Popular
  • Feedback
  • Contest
    • IoT Hardware Contest
    • 'AI & Open Hardware' Contest
    • 2nd Electronics Design Contest
    • 1st Electronics Design Contest
    •  View All Contest
  • Forum
  • Support
    • Sponsorships
    • Forum
    • Wiki
    • Affiliate Program
    • Redeem Gifts
    • Help
Create a project  Sign In

Oliver Scheifinger

  • Posts
    6
  • Followers
    1
  • Following
    0
+Follow
  • Shared Projects
  • Feedback
  • Like
  • Followers
  • Following
  • A foldable, print in place case with live hinges for the Raspberry Pi 5 with Active Cooler

    M!N!MAL 5 CH - Raspberry Pi 5 Case

    221
    0
    8
  • A foldable, print in place, live hinge case for the Raspberry Pi 5 without cooling

    M!N!MAL 5 - Raspberry Pi 5 Case

    264
    0
    8
  • A minimal, foldable print in place case / housing / sleeve for the Raspberry Pi Pico with live hinges

    M!N!MAL Pico - Raspberry Pi Pico Case

    248
    0
    8
  • A minimal, foldable print in place, housing for the Raspberry Pi Zero 2 or Banana Pi M2 with cooling and heatsink.

    M!N!MAL 0 CH - Raspberry Pi Zero2 case w. cooling / heatsink

    222
    0
    8
  • A minimal, foldable print in place case / housing / sleeve for the Raspberry Pi Zero 2 with live hinges (with cooling)

    M!N!MAL 0 C - Raspberry Pi Zero 2 Case with Cooling

    1925
    0
    9
  • This is the reduced to the max case / housing / sleeve for the Raspberry Pi Zero (2 W) in the version without cooling (we have another model that is prepared for cooling), less is hard to imagine. A foldable print in place housing with live hinge that is less than 2mm bigger than the Raspberry itself. All interfaces are accessible and the board itself is covered and protected. Above that it prints as one piece, the assembly is easy and no tools or screws are needed. Just print (in less than an half an hour / under 15 minutes with input shaping) and use…

    M!N!MAL 0 - Raspberry Pi Zero 2 Case

    240
    0
    8

About Elecrow

  • About Us
  • Contact Us
  • Forum
  • Blog
  • Wiki
  • Sitemap
  • Github
  • Coupons

Elecrow Policy

  • Shipping & Returns
  • Terms and conditions
  • Payment
  • Privacy Policy
  • Reward Points & Coins
  • intellectual property rights

Cooperation

  • Become a distributor
  • Sponsorships
  • Become an Affiliate
  • Sell on Elecrow
  • Seller Policy

Brand

  • CrowPanel-HMI Display
  • CrowView Note
  • CrowView
  • CrowPi
  • GrowCube
  • Crowbits
  • Letscode
 

Social media

Facebook Twitter Linkedin Youtube Instagram Discord

Payment methods

©Copyright 2012 - 2025 ELECROW All rights reserved.