[Home Assistant Ready] Comes with dedicated Home Assistant firmware pre-installed for easy integration with your existing smart home system.
[7-Inch IPS Touchscreen] Features a 1024 × 600 IPS display with 400 cd/m² typical brightness and responsive capacitive touch.
[Your Existing Dashboard] Access and control your Home Assistant devices, scenes, switches, and automations directly from the panel.
[ESP32-P4 & Wi-Fi 6] Combines ESP32-P4 processing with ESP32-C6 wireless connectivity, supporting Wi-Fi 6 and Bluetooth 5.3.
[Audio & Expansion Interfaces] Features dual speakers, microphones, USB, UART, I2C, and GPIO interfaces.
Note: Housing is not included.
Make smart home control easier with this 7inch Home Assistant touchscreen panel. Built on the CrowPanel Advanced ESP32-P4 HMI platform, it comes with dedicated Home Assistant firmware pre-installed, turning the display into a convenient control center for your existing smart home system.
Simply connect the panel to your Wi-Fi network and link it to your Home Assistant server. You can then access your existing dashboards, check device status, control smart lights and switches, adjust settings, and manage automations directly from the touchscreen.
Featuring a 7-inch IPS display with 1024 × 600 resolution and responsive capacitive touch, this compact panel is suitable for wall-mounted smart home control in your living room, bedroom, office, or garage.
No need to develop custom ESP32 firmware or build a separate HMI interface. Just connect, configure, and control your smart home from one dedicated screen.
Whether you want to turn off the lights before bedtime, check indoor conditions from your bedroom, or monitor connected devices in your garage, this 7-inch panel gives you a convenient way to interact with your Home Assistant system.
Note: This 7inch screen does not include the housing.
Important Note: This panel runs dedicated Home Assistant firmware with Secure Boot and Flash encryption enabled. Custom or third-party firmware (such as ESPHome, Arduino, or ESP-IDF programs) cannot be flashed on it. For custom firmware development, please select CrowPanel Advanced 10.1" ESP32-P4.
Important Note: Please do not force-flash any other firmware onto the device, as this may cause it to become unusable. Elecrow cannot provide technical support or after-sales service for issues resulting from forced installation of unofficial firmware.
Simple Setup
Getting started requires just a few steps:
Once connected, the panel displays your existing Home Assistant dashboard. Changes made to your dashboard are reflected on the panel, so you don't need to maintain a separate interface.
Requirements
Please Note: This panel does not replace your Home Assistant server and is not a standalone smart home hub. It requires an existing Home Assistant installation to work.
Perfect for
|
Main Chip-ESP32-P4NRW32 |
|
|
CPU/SoC |
ESP32-P4 RISC-V 32-bit dual-core processor for HP systems, running at up to 400 MHz; RISC-V 32-bit single-core processor for LP systems, running at up to 40 MHz |
|
System Memory |
768 KB L2MEM(HP) 32 KB SRAM(LP) 8 KB TCM 32 MB PSRAM |
|
Memory |
128 KB ROM(HP) 16 KB ROM(LP) 16 MB Flash |
|
Screen |
|
|
Size |
7.0 inch |
|
Resolution |
1024*600 |
|
Display Panel |
IPS Panel |
|
Touch Panel |
Capacitive Touch, Single/5-point Touch |
|
Viewing Angle |
178° |
|
Brightness |
400 cd/m²(Typ.) |
|
Color Depth |
16.7M (8-bit) |
|
Wireless Communication - Onboard Antenna |
|
|
WiFi |
Support 2.4GHz(Wi-Fi6), 802.11b/g/n |
|
Bluetooth |
Support Bluetooth 5.3 and BLE |
|
Interface/Function |
|
|
Interface |
USB2.0, UART, I2C, GPIO female headers, SD card holder, battery socket, speaker jack, camera header, module female headers, etc. |
|
Function |
Audio amplifier, battery charge management, USB to UART, microphones, dual speakers, etc. |
|
Speaker Connector |
|
|
Model |
BX-PH 2.0-2PWT |
|
Number of Pins |
1x2P |
|
Pin Pitch |
2mm |
|
Dimensions(L*W*H) |
8*8.5*5.6mm |
|
Mounting Type |
SMT Right Angle |
|
Button/LED Indicator |
|
|
Reset Button |
Yes, press to reset the device |
|
Boot Button |
Yes, press and hold the power button to burn the program |
|
Power Button |
Switch On/Off |
|
PWR |
Device power on/off indication |
|
CHG |
Lithium battery charging status, Low battery state |
|
Other |
|
|
Installation method |
All around mounting holes(M3 3.2mm), embedded, shell assembly |
|
Operating temperature |
-20~70 °C |
|
Storage temperature |
-30~80 °C |
|
Power Input |
5V/2A, USB or UART terminal |
|
Active Area |
155mm*87mm |
|
Dimensions |
180*105mm |