TEMP&HUM ±5%RH for RASPBERRY PI PICO

TEMP&HUM ±5%RH for RASPBERRY PI PICO

Centure24 4-Channel DSP Class-D Amplifier

$185.00
Availability: In stock
SKU
PDA08904P
Weight
450g
  • Buy 10 for $166.50 each and save 10%

Centure 24 is a compact 4-channel Class-D amplifier module with a fully digital signal path. It pairs an Analog Devices ADAU1466 DSP with a Texas Instruments TAS6584/TAS6684 I2S-to-PWM modulator and output stage, delivering up to 100 W per channel into 4 Ω. Channels can run as four BTL outputs or be paralleled (PBTL) for higher current into low-impedance loads. Audio comes in over USB, S/PDIF or I2S, and crossovers, EQ, time alignment and limiting are set with the free YorkStudio application.

Analog interface board provides two analog balanced or SE input channels

 

Four amplified channels with DSP on one board

Centure 24 is designed for active and multiway loudspeakers, subwoofers and plate-amplifier installations. It combines the DSP, the amplifier stage and a control MCU on a single board that works as a stand-alone amplifier or as the core of a plate-amp module.

Audio enters over USB, S/PDIF or the I2S bus, is processed by the ADAU1466, and is converted straight to PWM and amplified by the TAS6584/TAS6684. There is no analog stage between the DSP and the power stage.

Configuration: YorkStudio

The module is set up and tuned in YorkStudio, the YorkDevices configuration app. Connect it over the York USB interface and adjust the processing live. 

The YorkStudio guide has screenshots and a step-by-step walkthrough.

BTL and PBTL output modes

In BTL mode the module drives four independent speaker channels, up to 100 W each into 4 Ω and about 400 W combined. In PBTL (parallel bridge-tied load) mode, two BTL channels are paralleled into one output. This doubles the available output current, so a PBTL channel can drive low-impedance loads such as a 2 Ω woofer or subwoofer. Supported layouts are 4 × BTL, 2 × PBTL, or 2 × BTL + 1 × PBTL – for example, a 2-way speaker with BTL tweeter channels and a PBTL woofer channel.

Three input types

The built-in USB interface provides 2-channel USB Audio Class 2 at 48, 96 or 192 kHz and works without drivers on Windows, macOS and Linux. S/PDIF input and output are available on the audio header. The I2S input carries two data lines for four channels and can be synchronous to the 24.576 MHz master clock or asynchronous through the on-board sample-rate converter. Analog sources connect through an ADC over I2S, for example on the optional interface board.

On-board DSP

Crossovers, parametric EQ, time alignment, level and limiting are processed on board, with any input routable to any amplifier channel or to the S/PDIF output. Each channel has level, PEQ, crossover, compressor, mute, delay and polarity controls.

Load diagnostics and monitoring

Built-in diagnostics include DC load detection, AC impedance measurement and tweeter detection. When enabled, DC load detection automatically disables unloaded channels. Supply voltage and temperature are reported live in YorkStudio.

YorkStudio configuration software

YorkStudio is a free application for Windows, macOS and Linux. It detects the module automatically over USB and reads its current settings. Settings written to the module are stored in non-volatile memory and applied at power-up, so the amplifier runs without a computer once configured. Projects are saved as portable XML files.

Plate-amp ready

The signal and control interfaces (S/PDIF, I2S, I2C, GPIO) are routed to headers that mate with an optional companion interface board. The interface board carries an ADC for analog input, a USB-C connector, two status LEDs, a master-volume potentiometer and footprints for XLR or RCA inputs. The module supplies regulated 12 V and 3.3 V to power it.

Protection and updates

The amplifier has short-circuit protection and output-to-supply and output-to-ground protection. An on-board bootloader supports firmware updates through YorkStudio, with the configuration preserved.

FEATURES

- 4-channel Class-D amplifier with integrated DSP

- Output modes: 4 × BTL, 2 × PBTL, or 2 × BTL + 1 × PBTL

- Up to 100 W per channel into 4 Ω (BTL), about 400 W combined

- PBTL mode for higher current into low-impedance woofers and subwoofers

- Texas Instruments TAS6584/TAS6684 integrated modulator and output stage

- Analog Devices ADAU1466 DSP: crossovers, PEQ, time alignment, limiting

- Fully digital signal path from input to speaker terminals

- USB Audio Class 2, 2 channels, 48 / 96 / 192 kHz, driverless

- S/PDIF input and output, I2S input with ASRC

- Load diagnostics: DC load detection, AC impedance measurement, tweeter detection

- Live supply voltage and temperature monitoring

- 12–45 V DC single supply

- Firmware updates over USB

- Plate-amp form factor with optional interface board

- THD+N: < 0.03% at 1 kHz, 100 W

- Dimensions: 95 × 110 mm

 

INSTALLATION NOTES

- Outputs are bridge-tied. Never connect a speaker terminal to ground or chassis, and never join outputs of different channels except as set up for PBTL mode.

- Observe supply polarity. The module has no reverse-polarity protection.

- Header signals are 3.3 V logic level.

PACKAGE LIST

1 × Centure 24 v3 amplifier module

1x Analog interface module (with USB connector)

1x Master gain potentiometer

2x XLR connectors

10x 6.3 mm blade connctors

1x 12 pin ribbon cable

1x 20 pin ribbon cable

RESOURCES

Product page: https://york-devices.com/index.php?page=device&id=centure-24

Datasheet: https://york-devices.com/docs/centure24_v2_datasheet.pdf

YorkStudio software: https://york-devices.com/index.php?page=sw&tool=yorkstudio

YorkStudio user guide: https://york-devices.com/index.php?page=guide&tool=studio

 

Write Your Own Review
You're reviewing:Centure24 4-Channel DSP Class-D Amplifier
Your Rating
loading
Warranty Service

Warranty

Service

VIP Distributor Discount

VIP Distributor

Discount

Professional Tech Support

Professional

Tech Support

Fast Delivery

Fast

Delivery

×
ok  Add to cart successfully!
Customers Who View This Item Also Bought
left right