PiEEG Pi 5 Enclosure – 3D-Printed PLA Case for PiEEG-8 & PiEEG-16
One 3D-printed PLA case for a Raspberry Pi 5 with either a PiEEG-8or a PiEEG-16 shield on top. The lid has two slots that sit right over the electrode headers of both shields, so you can plug in electrode leads with the case closed. Four screws hold the lid at the corners, so it opens again easily.
Key Features
One case for PiEEG-8 and PiEEG-16 – both shields share the Raspberry Pi HAT footprint. The lid's left slot sits over electrodes 1–8. The right slot sits over electrodes 9–16 on PiEEG-16, or over the jumpers on PiEEG-8.
Connect electrodes with the lid closed – leads plug in through the two lid slots.
Shaped around the Raspberry Pi 5 – openings for USB-C power, both micro-HDMI ports, USB, Ethernet and the microSD slot, plus side vents for airflow.
Standard mounting – four posts at the Raspberry Pi's 58 × 49 mm mounting holes.
Non-conductive PLA – stiff, light and safe around the shield's electronics.
Open-source and repairable – the STL files are open source, so you can print a spare case or lid yourself.
Four-step assembly – needs only a small Phillips screwdriver.
Specifications
Compatible shields
PiEEG-8, PiEEG-16
Host board
Raspberry Pi 5 (openings follow the Pi 5 port layout)
Material
PLA (non-conductive), FDM 3D printed
Printed parts
2 – case body and lid
Case body
105.8 × 75.2 × 35.5 mm
Lid
105.8 × 75.2 × 3.6 mm (including the four screw ears)
Assembled size
approx. 106 × 75 × 37 mm
Lid fixing
4 × M2.5 × 8 mm cscrews through countersunk ears into the corner lugs
Pi mounting
4 posts at 58 × 49 mm (standard Raspberry Pi holes)
Openings
USB-C, 2 × micro-HDMI, USB, Ethernet, microSD, side vents, 2 lid slots for electrode leads
Weight
approx. 35–45 g
Assembly
Place the Raspberry Pi 5 on the four posts in the case.
Plug the PiEEG-8 or PiEEG-16 onto the Pi's 40-pin GPIO header.
Put the lid on. The left slot sits over electrodes 1–8; the right slot sits over electrodes 9–16 (PiEEG-16) or the jumpers (PiEEG-8).
Insert and tighten the 4 lid screws at the corners.
Fit the shield only while the Raspberry Pi is unpowered.
Package Contents
1 × Case body for Raspberry Pi 5 (PLA, with four mounting posts, Pi 5 port openings and side vents)
1 × PiEEG-8/16 lid with screw ears (PLA, two slots over the electrode headers, countersunk screw holes)
4 × M2.5 countersunk lid screws
Required for Operation (Not Included)
Raspberry Pi 5
PiEEG-8 or PiEEG-16 shield
Small Phillips screwdriver
5 V USB battery power bank (mandatory for mains isolation during human recording)
FAQ
Does the same case fit both PiEEG-8 and PiEEG-16? Yes. Both shields have the same outline and mounting holes and plug onto the same 40-pin header. The lid's slots line up with the electrode headers on both boards.
Will it fit a Raspberry Pi 4? No. The case is designed for the Raspberry Pi 5. The Pi 4 has its USB and Ethernet ports in different places, so the side openings won't line up.
Is PLA suitable for this case? Yes, at room and body temperature. PLA softens at around 55–60 °C, so don't leave the case in a hot car or in direct summer sun.